Toyota Tacoma 2015-2018 Service Manual: Disassembly

Toyota Tacoma 2015-2018 Service Manual: Disassembly

DISASSEMBLY

PROCEDURE

1. REMOVE ROOM LIGHT BRACKET

(a) Disengage the guide to remove the room light bracket.

2. REMOVE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY

(a) Remove the 2 bolts and sliding roof drive gear sub-assembly.

3. REMOVE SUNSHADE TRIM SUB-ASSEMBLY

(a) Remove the screw.

(b) Disengage the claw and 2 guides to remove the sliding roof drain hose joint LH as shown in the illustration.

(c) Remove the screw.

(d) Disengage the claw and 2 guides to remove the sliding roof drain hose joint RH as shown in the illustration.

(e) Slide and remove the sunshade trim sub-assembly as shown in the illustration.

4. REMOVE ROOF DRIP CHANNEL

(a) Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws.

Text in Illustration

*a

Protective Tape

(b) Slide and remove the roof drip channel as shown in the illustration.

5. REMOVE SLIDING ROOF DRIVE CABLE SUB-ASSEMBLY LH

NOTICE:

Do not disassemble the sliding roof drive cable sub-assembly except when replacing it.

(a) Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws to remove the sliding roof guide block.

Text in Illustration

*a

Protective Tape

(b) Remove the sliding roof drive cable sub-assembly LH.

6. REMOVE SLIDING ROOF DRIVE CABLE SUB-ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.

Removal
REMOVAL PROCEDURE 1. REMOVE SLIDING ROOF SIDE GARNISH LH (a) Fully open the sunshade trim sub-assembly. (b) Remove the sliding roof side garnish LH. ...
Other materials:

Problem Symptoms Table
PROBLEM SYMPTOMS TABLE HINT: Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed in order of probability in the "Suspected Area" column of the table. Check each sy ...

Installation
INSTALLATION PROCEDURE 1. INSTALL TRANSMISSION FLOOR SHIFT ASSEMBLY (a) Install the transmission floor shift assembly to the vehicle body with the 4 bolts. Torque: 14 N·m {143 kgf·cm, 10 ft·lbf} (b) Attach the 4 clamps to connect the wire harness to the transmission floor shift assembl ...

Check Mode Procedure
CHECK MODE PROCEDURE 1. DESCRIPTION Check mode has a higher sensitivity to malfunctions and can detect malfunctions that cannot be detected in normal mode. Check mode can also detect all of the malfunctions that can be detected in normal mode.

Related news

  • Chrysler 200: Premium System – If Equipped
  • Toyota Highlander Service Manual: Outside moulding
  • Toyota Sienna Service Manual: Diagnostic trouble code chart
  • Kia Optima: Power Seat Control Switch. Repair procedures
  • Toyota Corolla Repair Manual: Wireless door lock control system

  • Toyota Tacoma 2015-2018 Service Manual: Disassembly

    Toyota Tacoma 2015-2018 Service Manual: Disassembly

    Toyota Tacoma 2015-2018 Service Manual: Disassembly

    Toyota Tacoma 2015-2018 Service Manual: Disassembly

    Toyota Tacoma 2015-2018 Service Manual: Disassembly

    Toyota Tacoma 2015-2018 Service Manual: Disassembly

    Toyota Tacoma 2015-2018 Service Manual: Disassembly

    Toyota Tacoma 2015-2018 Service Manual: Disassembly

    Toyota Tacoma 2015-2018 Service Manual: Disassembly

    Toyota Tacoma 2015-2018 Service Manual: Disassembly

    Toyota Tacoma 2015-2018 Service Manual: Disassembly

    Toyota Tacoma 2015-2018 Service Manual: Disassembly

    Toyota Tacoma 2015-2018 Service Manual: Disassembly

    Toyota Tacoma 2015-2018 Service Manual: Disassembly

    Toyota Tacoma 2015-2018 Service Manual: Disassembly

    Toyota Tacoma 2015-2018 Service Manual: Disassembly

    Toyota Tacoma 2015-2018 Service Manual: Disassembly

    Toyota Tacoma 2015-2018 Service Manual: Disassembly

    Toyota Tacoma 2015-2018 Service Manual: Disassembly

    Toyota Tacoma 2015-2018 Service Manual: Disassembly

    Toyota Tacoma 2015-2018 Service Manual: Disassembly

    Toyota Tacoma 2015-2018 Service Manual: Disassembly